Williams System 9 - 11

From PinWiki
Jump to navigation Jump to search
ExclamationPoint.jpg
Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.


1 Introduction

Put system info here

Williams System 9 Board Set


2 Games

2.1 System 9

  • Space Shuttle
  • Sorcerer
  • Comet

2.2 System 11

  • Grand Lizard
  • High Speed
  • Road Kings
  • Gold Mine (Shuffle Alley)

2.3 System 11a

  • Pinbot
  • Millionaire
  • F-14 Tomcat
  • Fire!
  • Fire! Champagne Edition

2.4 System 11b

  • Big Guns
  • Space Station
  • Cyclone
  • Banzai Run
  • Swords of Fury
  • Taxi
  • Jokerz!
  • Earthshaker
  • Black Knight 2000
  • Police Force
  • Elvira and the Party Monsters
  • Bad Cats
  • Mousin' Around!
  • Whirlwind

2.5 System 11c

  • The Bally Game Show
  • Pool Sharks
  • Rollergames
  • Diner
  • Radical!
  • Dr. Dude
  • Riverboat Gambler
  • Bugs Bunny's Birthday Ball

3 Technical Info

The System 11 Board Set
System 9 eliminated a huge issue with the earlier system 3 through 7 boardsets - the 40 pin interconnector used between the MPU and Driver boards. Now, all the circuitry of the mpu, driver, and sound boards was contained on one board. Helper boards were still used for displays, speech, special purposes, and solenoid expansion. Starting with Banzai Run, Williams re-introduced a weak link into their system: the interconnect board, itself designed to eliminate many under playfield flasher driver boards, which had proven themselves problematic.

One of the largest advantages of the system 11 board set is its ability to switch one set of coil driver transistors between 2 sets of coils/flashers. It does this via a relay on a separate board called the A/C relay. The theory is that coils that are seldom fired will be on the A side of the relay, and that flashers will be on the C side of the relay. Most of the time during gameplay, the C side is active, letting the flashers be driven. If the driver transistor for the A/C relay itself is bad, the relay defaults to the coil side, allowing the game continue to operate in a semi-normal fashion (usually the A side coils are the ball shooter lane, drop target resets, VUK - basically coils that don't need to be able to operate 100% of the time like a sling coil or pop bumper coil. (Data East's boardset was essentially a copy of the system 11 boardset - but they programmed it the opposite way, so that the flasher side of the A/C relay is active by default. So on a Data East game when the A/C relay doesn't operate, the game just sits there and flashes lamps instead of playing.)

System 9 and early system 11 games do share a disadvantage with the earlier 3-7 boardsets - they still utilize special solenoid circuitry. The pops and slings on system 9/11 games do not activate a switch which is seen by the mpu's program which fires the coil - instead, the switches directly fire their associated coils via some logic gates on the main board. The main disadvantage with this system is that the solenoids fire continuously as long as their activation switch is closed; a locked on sling or pop will burn out components quickly. It is recommended to add a 1, 1.5, or 2 amp inline fuse to each coil on a directly fired system 11 game. (Usually just the pops and slings are direct fired coils).

4 Problems and Solutions

4.1 Power Problems

Replacement power supply If using the Rottendog WDP011A power supply for Williams Cyclone or Big Guns, you may have to move the +12v jumper from the bottom jump to the top. If your machine has GI but doesn't boot (only the 5v light on the CPU is lit) and is one of these two games, that is the most likely reason.

4.2 MPU boot issues

4.2.1 Relocating the battery from the MPU board

4.2.2 Installing NVRAM instead of batteries

Like most other pinball mpu boards, you can replace the battery-backed ram with a non-volatile memory ram. Unlike most other systems, you have to jumper around a diode so the game will boot. D1, a 1n5817 diode, has a very low forward voltage drop (about 0.2 volts) vs. the normal 0.4-0.6 volts most other diodes have. If you replace U25 with the memory ram, most memory ram will not unlock and allow writes until the voltage is 4.8 volts or so. The 1n5817 D1 diode is just enough to prevent most memory rams from allowing writes. To solve this, solder a jumper wire around the D1 terminals, or remove D1 entirely and replace with a jumper. Make sure you do not have batteries installed if you do this as they will simply short to ground, get hot, and leak. It's recommends to remove D2 and the battery holder entirely if you do this so this will never be a possibility, and write with a sharpie where the battery holder was "upgraded to NVRAM".

You need a replacement ram that can replace a 6116 or a 6264. These are becoming scarce, but there are other solutions coming out that use surface mount equivalents on a small circuit board that plugs into the RAM's socket. Unfortunately, U25 is soldered in on most system 11 boards and would need to be removed to replace with an NVRAM.

4.2.3 Installing a memory capacitor instead of batteries

A 5.5 volt 1.5 farad capacitor can be installed in place of batteries. To do so, remove the battery holder and install the + lead of the memory capacitor bent into a dogleg shape in the + hole that feeds diode D2. (The memory cap should be mounted slightly off the board. This is the purpose of the dogleg bend, but if you have a mica insulator that will work also.) Fold the - lead on the capacitor flat and solder a small jumper wire to it that goes to the main negative terminal where the battery holder was; this is diagonally opposite the + lead in most cases, but double check with a meter. Make sure you heat shrink this connection so it doesn't short out against any traces or pads in the area.

To allow the capacitor to charge, you need to jumper around diode D2, or remove it entirely and replace with a jumper wire. A full charge may take 8-12 hours, but once the memory capacitor is charged, turning the machine on for a about 30 minutes a month is enough to keep the capacitor charged up.

4.2.4 Repairing Alkaline Corrosion

Remove the battery holder entirely from the MPU board and wash the board's affected areas with a 50/50 mix of vinegar and water. Scrub the corrosion with a soft toothbrush, rinse with water, then rinse with 91% or 99% isopropyl alcohol to displace the water. Unfortunately on system 11 boards often the corrosion will eat into traces that are beneath PIA chips (U41/U42) and you might have to desolder the chips to remove the corrosion and repair traces.

4.2.5 Connecting a logic probe to the MPU

4.2.6 Using a PC Power Supply For Bench Testing

4.3 Game resets

4.4 Solenoid problems

this is a stub

4.4.1 A/C solenoid/flasher problems

this is a stub

4.4.2 Special solenoid problems

this is a stub

4.5 Lamp problems

4.6 Switch problems

4.7 Display problems

System 9/11 High Voltage Section Repair

WARNING: This circuit uses high voltages. Don't continue, unless you are confident in your diagnostic abilities.

Check Voltages

If all displays are blank, your high voltage (HV) section may not be working. On the Power Supply Board, use a DMM set to DC volts with the - lead grounded, probe the following connector pins to determine if the HV section needs repair. If the display fuse, F1 is blowing, you should remove the applicable display connector (with power off) before testing the voltages.

If you have Power Supply D-11883 or D-12246:

3J2 pin 1 = -100 volts DC
3J2 pin 3 = +100 volts DC

If you have Power Supply D-8345-xxx:

3J5 pin 3 = -100 volts DC
3J5 pin 4 = +100 volts DC

If the test points are more than about 5 volts out of spec, then your HV section may be malfunctioning (if you or a previous owner replaced Z2/Z4 with 1N4763A diodes to purposely reduce the display voltage, test readings in the 90's range would be normal).

Check the table below for a solution.

Troubleshooting table

Symptom Possible Cause Replacement
0V ON BOTH +100/-100 lines Check F1 1/4 Amp SB
0V on +100V line Open Diode D3 1N4004
Open Q2 2N5401
Shorted Zeners 1N4730A and 1N4763A
Open Q1 MJE340
0V on -100V line Open Diode D4 1N4004
Open Q4 2N5551
Shorted Zeners 1N4730A and 1N4763A
Open Q3 MJE350
F1 1/4 Amp Fuse Blows Bad Capacitor at C1 and C3 100uF,150V
Shorted Display Display Glass*
Shorted UDN7180 UDN7180*
Shorted UDN6118 UDN6118*
+118V on +100V line Shorted Q1 MJE340
-118V on -100V line Shorted Q2 MJE350
* located on display board


Display Fuse F1 Blows

Testing the UDN Chips

If the display fuse is blowing, you should check the display board for shorts before connecting a new or rebuilt power supply to the display board, as a shorted display or chip can damage a good power supply. Remove the display board from the system. The display characters are driven by the two types of UDN chips, the UDN7180 & UDN6118 (or UDN6184). Locate these chips (there are several) on the board and test them with your DMM set to diode check. Clip your + (RED) lead to the ground trace of the board. Probe the UDN chips as shown in the diagram. If any shorts are read in the tested pins, the display should not be connected to the power supply until the shorts are corrected. UDNReading.png

Shorts Are Found in UDN Chip Test
If a short reading is found in the tested pins (don't test the pins labeled 'dont care'), the UDN chip should carefully be desoldered and removed from the board. Take care to preserve this chip, as they are nearly impossible to find and expensive to replace. Now install an IC socket in its place. Repeat the test with no chip installed. If the short is gone, then the UDN chip needs to be replaced. If the short remains, then the display glass needs to be replaced.

Displays Test With no Shorts
Once the displays are tested and shorts are eliminated, we can proceed with the HV section repair.

Replacing the components in the HV Section
Since there are not that many components, if you are having problems isolating the fault, a quick solution is to replace all the components in the HV section. If only one side (+ or -) is failing, it is possible to rebuild only the failing side. Check the parts section of the wiki to find suppliers, and get the replacement parts for one or both failing sides:

Part +Side Part -Side Part +,-Location
Transistor MJE340 (or MJE15030) MJE350 (or MJE15031) Q1,Q3
Transistor 2N5401 2N5551 Q2,Q4
Zener diode 1N4730A 1N4730A Z1,Z3
Zener diode 1N4763A** 1N4763A** Z2,Z4
Resistor 39k Ohm,1W 39k Ohm,1W R1,R4
Resistor 680 Ohm,1/4W 680 Ohm,1/4W R2,R5
Resistor 330k Ohm,1/2W 330k Ohm,1/2W R3,R6
Capacitor 0.1uF,250V metal polyester 0.1uF,250V metal polyester C2,C4
Capacitor 100uF,150V 100uF,150V C1,C3
**This is a 91V Zener to reduce the voltage to prolong display life


Remove and replace HV components

  • Clip the old components from the board (make sure you have new ones first).
  • Use one of the desoldering methods to remove solder from the holes.
  • Stuff board with new components.
  • Check for correct orientation on transistors, diodes and the large capacitor if you replace it.
  • Leave a little space under components for air flow.
  • Bend leads on components so they won't fall out when board is inverted for soldering.
  • Double check that all the correct parts are in the correct places and properly oriented.
  • Solder the parts to the board
  • Clip excess off leads


NOTE ON INSTALLATION OF THE MJE340/MJE350 TRANSISTOR
The MJE340/MJE350 is the heat-sinked transistor. On most Williams boards, this transistor pin configuration is not the same as the original part. It will need to be installed vertically with heat sink attached to the transistor only. The transistor will sit at about a 45 degree angle so the legs can be lined up to fit in the correct holes.

Check your board and insure correct orientation before soldering in place. Late versions of the System 11 series boards were designed to use the pin configuration of the MJE340/MJE350 transistors.

Do not mount vertically if the power supply is designed to use the pin configurations of the newer transistors!

MJEInstall.png
NOTE: The MJE15030/MJE15031 are rated for higher power and can be used instead of the MJE340/MJE350, but the MJE340/MJE350 are well within design specifications and are suitable replacements at 1/3 the cost of the MJE15030/MJE15031.


Ready to test

To test the rebuilt power supply, return to the "Check Voltages" section of this guide.

Other Resources
The System 9-11 HV section of the PSU is very similar in design to the earlier System 3-7. So it will be worth reading through the Sys 3-7 PSU Problems section entitled +/-100v Display HV Section of PSU, for some more detail. It also provides links to source complete HV rebuild kits which will normally cost under $10 shipped.

4.8 Sound problems

System 11 games are known to have some amount of hum. An easy thing to test is to make sure all boards are secured tightly with all screws. This will insure the boards have a proper ground.

Another cause of hum could by an inconsistent +5 volts from the power driver board. An indicator of this being the cause of your hum would be the game occasionally resetting as well. Replacing caps C8 and C10 on the power board may fix this issue.

4.9 Flipper problems

4.10 Pop bumper problems

5 Repair Logs

Did you do a repair? Log it here as a possible solution for others.